Tips to Protect Your Pipes

The winter months are coming!  Spend a few minutes reading this article to learn how you can prevent frozen pipes using these 10 tips.

1)Insulate your pipes

One of the best ways to protect your pipes is to insulate them. This will help to keep the water in the pipes from freezing, which can cause the pipes to burst. You can purchase pipe insulation at most hardware stores. Be sure to measure the circumference and length of your pipes before purchasing the insulation so that you get the correct size. Once you have the insulation, simply cut it to size and slip it over the pipe. You may need to use tape or zip ties to keep the insulation in place.

2)Secure basement doors, windows and crawl space openings

Your basement is the most vulnerable part of your home when it comes to flooding and water damage. That’s why it’s important to take measures to protect your basement from water intrusion.

One of the best ways to do this is to make sure all doors, windows and openings to your basement are properly sealed and waterproofed. This will help keep water out in the event of a flood or major leak.

You should also consider installing a sump pump in your basement to help remove any water that does manage to get in. And finally, make sure you have adequate insurance coverage in case of any water damage that does occur.

3)Drain outside waterlines

If you have any outdoor water lines, be sure to drain them before the cold weather hits. Water that is left in these lines can freeze and cause the pipes to burst. To drain your outdoor water lines:

– Turn off the water supply to the line at the indoor shut-off valve.

– Open all of the outdoor faucets connected to the line to allow any water remaining in the line to drain out.

– Once all of the water has drained from the line, close the outdoor faucets.

4)Apply electrically-powered tape to pipes

If you’re looking for a quick and easy way to protect your pipes, electrically-powered tape is the way to go. This type of tape is designed to be applied quickly and easily, and it will provide a reliable layer of protection against freezing temperatures. Here’s how to apply it:

1. Start by cleaning the surface of the pipe that you’ll be applying the tape to. This will help ensure that the tape adheres properly.

2. Once the surface is clean, cut the electrically-powered tape to length and peel off the backing.

3. Apply the tape to the pipe, starting at one end and working your way around. Be sure to overlap each layer by about half an inch.

4. Once you’ve wrapped the entire pipe, plug in the power cord and turn on the power supply. The tape will heat up and create a seal around the pipe.

5. Let the seal cool for a few minutes before touching it or applying any pressure to it. Once it’s cooled, your pipe should be protected from freezing temperatures for several hours.

5)Wrap your water heater with an approved manufacturer’s blanket

If your home is not already equipped with a water heater blanket, now is the time to invest in one. A water heater blanket helps to insulate your water heater, keeping the water inside nice and warm. This is especially important in winter months when temperatures can drop significantly. By wrapping your water heater with an approved manufacturer’s blanket, you can save money on your energy bill and extend the life of your water heater.

6)Open cabinet doors

If your pipes are located in cabinets, make sure to open the doors when cold weather hits. This will allow warm air to circulate around the pipes and prevent them from freezing.

7)Keep faucets running

running faucet

If the temperature outside is close to freezing, or if you know a hard freeze is coming, take the following precautions:

-Keep a slow trickle of water running through your faucets during cold weather. This will help prevent your pipes from freezing.

-Open cabinet doors underneath your sink to allow heat to reach the pipes.

-If you plan on being away from home for an extended period of time, have someone check on your house and make sure your heat is kept at a consistent temperature.

8)Know How to Check Your Water Pressure

If your home has a well or is on a municipal water system, you need to know how to check your water pressure. Most people don’t think about their water pressure until they have a problem with it. 

Water pressure problems can be caused by many things, including a broken or damaged pipe, a blockage in the line, or even a problem with the municipal water supply. If you suspect that you have a water pressure problem, the first thing you should do is check the pressure gauge on your water tank. 

If the gauge is reading below the normal range, then you likely have a low-pressure issue. Conversely, if the gauge is reading above the normal range, then you likely have a high-pressure issue. Once you’ve determined whether you have high or low water pressure, you can take steps to fix the problem. 

If you have low water pressure, there are a few things you can do to try to increase it. First, check all of your faucets and fixtures to see if they are fully open. If they are not, turn them on all the way and see if that increases your water pressure. 

If that doesn’t work,check your home’s main shut-off valve to see if it is fully open. The shut-off valve is usually located near where the main water line comes into your home. If it isn’t fully open, turn it until it is and then check your water pressure

9)Locate the main water shut-off valve and learn how to use it in the case of frozen pipes or burst pipes

main water shut-off valve

If a pipe in your home freezes or bursts, you’ll need to know how to shut off the main water valve to prevent further damage. The main water shut-off valve is usually located near the water meter or where the main water line enters your home.

To shut off the main water valve, turn it clockwise until it’s perpendicular to the pipe. Once the water is shut off, open all of your faucets to drain any remaining water from the pipes. You can then thaw frozen pipes with a hair dryer or by wrapping them in towels soaked in hot water, and repair burst pipes by replacing the damaged section of pipe.

10)Have a hair dryer handy, in case your pipes do freeze

If your pipes do freeze, it’s important to have a hair dryer handy so you can thaw them out as quickly as possible. You’ll want to start by thawing out the section of pipe that is closest to the faucet, so that water can start flowing through again. Once the water is flowing, you can move on to thawing out the rest of the pipes. Be sure to dry off any wet surfaces afterwards to prevent further freezing.

Get professional help!

If you have a problem with your pipes freezing, don’t hesitate to call Plumber To Your Door. We are your 24 hour plumber in Toronto and we’re here to help. We’ll come to your home or business and take care of the problem quickly and efficiently. We know that frozen pipes can be a real pain, so we’ll work quickly to get your water flowing again. We’ll also take measures to prevent the problem from happening again in the future. So if you need a 24 hour plumber in Toronto, call Plumber To Your Door. We’re here to help!

Read More: